Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterLock Repair in Boulder City, NV
Gate lock repair in Boulder City usually costs $95 to $260, and most jobs are finished on the first visit. That covers a stiff deadbolt, a keypad that quit accepting your code, a latch that no longer catches, or a lock that turns but won’t release the gate. If your gate lock is fighting you, call Ironworks Gate Co. Boulder City at (888) 276-7609.
We work on the locks and latches that live on driveway and estate gates: mechanical deadbolts, magnetic latches, electronic strikes, keypads, and the low-voltage wiring that ties them to the opener. A gate lock is not a house lock. It takes weather, dust, and thousands of open-and-close cycles a year, and it has to line up perfectly with a swinging or sliding leaf that may have shifted a quarter inch since it was hung. That is the work we do, and we back every job with a written 90-Day Done Right Promise.
This page sits under our main Gate Repair service, which covers the full range of gate problems from broken hinges to dead motors.
Key Takeaways
- Most gate lock repairs in Boulder City run $95 to $260 and are handled in one visit.
- We service keypads, strikes, and latches on DoorKing, LiftMaster, Elite, and other major automation brands.
- Upfront pricing is settled before any work starts, so the bill matches the quote.
- Every repair carries our written 90-Day Done Right Promise.
- A live person answers the phone at (888) 276-7609, day or night.
When You Need Lock Repair
Gate locks announce themselves in a handful of familiar ways. If any of these sound like your gate, it’s worth a look before the problem gets worse.
- The key turns but the gate won’t open. The lock cylinder is fine; the latch or strike has slipped out of alignment. This is common on gates that have settled into Boulder City’s caliche-heavy soil, where a small shift in the post throws off the whole lock line.
- The key is hard to turn or sticks. Grit, sun-baked lubricant, and fine desert dust work into the cylinder. Left alone, the key eventually snaps off in the lock.
- The keypad stopped accepting your code. On DoorKing and LiftMaster keypads, this is often a tired keypad, a loose connection, or a control board that needs resetting. We diagnose which one before recommending parts.
- The gate closes but the lock doesn’t catch. A gate that drifts open a few inches after closing usually has a latch that isn’t seating. That leaves the gate unsecured even though it looks shut.
- The latch is loose, bent, or worn through. Years of metal-on-metal contact wear down the latch and strike plate. On older gates around the Historic District, we often find hardware that has simply reached the end of its life.
- Someone forced the gate. A pried latch or bent strike needs more than a new lock; the gate frame and hinge alignment should be checked too.
If your gate is showing other symptoms too, our Gate Repair in Boulder City page covers the broader range of fixes.
Our Lock Repair Process
We keep the process simple and predictable. Here is how a typical lock repair visit runs.
- We listen and inspect. You tell us what the gate is doing. We check the lock, latch, strike, gate alignment, and, where it applies, the keypad and its wiring. We look at how the gate swings or slides, because a lock problem is often an alignment problem in disguise.
- We give you a price before we start. No-hassle upfront pricing, settled before a single bolt is turned. If we find something you didn’t expect, we tell you before we touch it.
- We repair or replace the right part. Sometimes the fix is a cleaned and re-keyed cylinder. Sometimes it’s a new latch, strike, or keypad. We carry the brands we service, including DoorKing and LiftMaster, so the correct part is on hand when we can.
- We realign the gate if needed. A new lock on a misaligned gate will fail again. If the leaf has drifted, we adjust hinges or the track so the lock lines up and stays lined up.
- We test it with you watching. Open, close, lock, unlock. We make sure the gate latches cleanly and the keypad works before we leave.
- We back it in writing. Every repair is covered by our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
If the gate needs work beyond the lock, we handle that too. Our technicians have up to 13 years of experience on gates and their automation.
Lock Repair Pricing in Boulder City
Gate lock repair in Boulder City typically runs $95 to $260, depending on the lock type and what’s actually wrong. Here is a rough breakdown of common jobs.
| Job | Typical price range |
|---|---|
| Clean, lubricate, and re-key a sticky cylinder | $95 – $140 |
| Replace a mechanical latch or strike plate | $130 – $200 |
| Replace or reprogram an electronic keypad | $150 – $260 |
| Diagnose and repair lock wiring or a control connection | $120 – $240 |
| Realign gate leaf so the lock seats properly | $110 – $220 |
What moves the price: the type of lock, whether it’s mechanical or electronic, whether we need to bring in a specialty part, and whether the gate needs realignment. Brand matters a little, since Elite and Mighty Mule hardware can differ from what’s on a LiftMaster system. We give you a firm quote before we start, so the number on the bill is the number we agreed on.
Two standing offers take the edge off the cost: $50 Off Any Repair Over $250, and a Free Second Opinion on Any Written Estimate if you’ve been quoted elsewhere. Seniors and veterans get a 5% discount, always. We also offer an $89 Seasonal Tune-Up, which is a good way to catch a worn latch before it fails.
Call (888) 276-7609 for a free estimate. A live person answers, day or night.
FAQs – Lock Repair
How much does gate lock repair cost in Boulder City?
Gate lock repair in Boulder City usually costs $95 to $260. Simple clean-and-re-key jobs land near the low end, while keypad replacement or wiring repair runs higher. Call (888) 276-7609 for an exact quote, which is free.
Can you fix my gate lock the same day?
Most gate lock repairs are finished in a single visit, and we aim for same-day service whenever the schedule allows. Call (888) 276-7609 and we’ll tell you the earliest we can be there.
My keypad stopped working. Can it be repaired or does it need replacing?
It depends on the cause. A keypad that stopped accepting codes is sometimes a wiring or control-board issue that we can repair, and sometimes the keypad itself has worn out and needs replacing. We diagnose it first, on brands including DoorKing and LiftMaster, and you get a price before any work starts. Call (888) 276-7609 to book a visit.
Is it cheaper to repair the lock or replace the whole gate lock assembly?
Repair is almost always cheaper when the lock hardware is sound and only the cylinder, latch, or strike has failed. Replacement makes sense when the assembly is bent, forced, or at the end of its life. We’ll tell you honestly which one your gate needs, with an upfront price either way. Call (888) 276-7609 for a free estimate.
Contact Ironworks Gate Co. Boulder City
If your gate lock is sticking, failing to catch, or refusing your keypad code, we can take a look. Ironworks Gate Co. Boulder City handles lock repair on driveways across Boulder City, and every job is backed in writing by our 90-Day Done Right Promise. Call (888) 276-7609 for a free estimate. A live person answers, 24 hours a day, 7 days a week.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City.