Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterAutomatic Gate Repair in Boulder City, NV
Automatic gate repair in Boulder City usually means one of three things: the operator stopped moving the gate, it moves but the safety sensors won’t let it close, or it works erratically because a limit switch or control board has drifted. Most of those we can diagnose and fix on the first visit, with the price settled before we touch a bolt. Ironworks Gate Co. is a gate specialist, not a general handyman outfit – our technicians have up to 13 years of experience and we’re trained and equipped on nine major automation brands so the correct fix is made the first time.
This part of our business is the automation side: the motor, the arms, the control board, the safety eyes, the keypad and the wireless receiver. If the problem is the gate structure itself – a sagging frame, torn hinge, bent picket or weld that has given way – that work falls under our Gate Repair service, and we’ll tell you plainly which one you’re dealing with. If you’d rather talk it through, a live person answers the phone 24 hours a day, 7 days a week at (888) 276-7609. No voicemail tree, no callback queue.
Boulder City is an older town with a lot of older gates. A swing operator that was installed twenty years ago on a brick pillar held by desert caliche is a different repair than a modern slide gate on a flat concrete pad. We know the difference, and we come out expecting to find it.
When You Need Automatic Gate Repair
Automatic gates rarely fail without warning. There’s usually a stretch of weeks where something is off, and the homeowner learns to live with it. These are the symptoms that tell us you shouldn’t:
- The gate reverses before it touches the stop. The safety eyes are out of alignment, dirty, or the reflector on the far post has faded in the sun. A live gate that repeatedly reverses mid-travel is the most common emergency we see, and it usually traces back to one of those.
- The operator hums or clicks but the gate doesn’t move. That’s typically a capacitor, a stripped drive gear, or a motor that has finally given out. On older LiftMaster arms this is a straightforward diagnosis; on some imported units it isn’t, which is exactly why we stock and service the brands we do.
- The gate opens and won’t close. Could be the photo-eye, could be a stuck limit switch, could be a keypad entry that’s holding the cycle open. We’ve seen a DoorKing board go into a fault loop after a power flicker during a monsoon storm, and we’ve seen the same symptom from a spider web across a sensor lens. Both are quick to sort once we’re standing at the gate.
- The remote works from the driveway and nowhere else. Range problems usually mean a failing receiver, a damaged antenna wire, or a battery that’s on its way out. Sometimes the fix is a new battery; sometimes it’s an Elite receiver that has aged out.
- The gate slams at the end of travel. That’s a limit adjustment or a worn arm bushing, and left alone it will eventually crack a hinge or shake loose the operator mounting bolts.
- Something is clicking, grinding, or screeching. Any metal-on-metal noise during travel is a warning. On a desert gate that sees 100-degree afternoons and fine airborne dust, the moving parts dry out faster than most people expect. A $89 seasonal tune-up will usually catch it before it becomes a repair.
If you recognize any of those, call (888) 276-7609. We’d rather come out on a click than replace a motor.
Our Automatic Gate Repair Process
- Answer the phone and listen. A real person picks up, day or night. We ask what the gate is doing, what brand it is if you know, and roughly when it started. That first conversation tells us which tools and which parts go on the truck, and it means we’re not guessing when we arrive.
- Come out and inspect before quoting. We put hands on the gate: the operator, the control board, the safety sensors, the keypad, the hinges and the track or swing arc. We’re not going to quote a motor replacement from the driveway without confirming the motor is the problem.
- Give you the price in writing, upfront. You see the number before we turn a bolt. If it’s a repair over $250, the standing $50 off comes off the bill. If you’ve had another estimate, bring it – we’ll give you a free second opinion in writing, whether or not you hire us.
- Make the repair. Most jobs are completed on the first visit, because the truck carries the common parts for the brands we service: LiftMaster, DoorKing, Mighty Mule, Elite, FAAC, BFT, Linear, Viking, Ghost Controls. If a specific part has to be ordered, we tell you straight and give you the timeline the same day.
- Test everything in front of you, including the safety devices. The photo-eye gets a walk-through test. The reverse-on-obstruction gets a test. The remote gets a test from the same spot you use it every morning. We don’t hand the keypad back until we’ve confirmed the whole cycle, not just the part we fixed.
- Back it up in writing. Every job is covered by our 90-Day Done Right Promise. If something we touched isn’t right, we come back and make it right. No paperwork, no arguing. That’s the Keystone Standard.
Automatic Gate Repair Pricing in Boulder City
Automatic gate repair pricing in Boulder City depends mostly on what has failed – a sensor, a control board, a motor, or the whole operator – and on how accessible the operator is. Below are the ranges we typically quote for the work. Every job gets a written upfront price before we start, and the range you see is the range we hold to.
| Repair | Typical Range | Notes |
|---|---|---|
| Safety sensor realignment or replacement | $120 – $240 | Most common single repair we run |
| Remote or keypad programming / replacement | $95 – $275 | Includes new receiver if needed |
| Limit switch adjustment or repair | $140 – $260 | Often fixes slamming at end of travel |
| Control board replacement | $280 – $620 | Brand-dependent; DoorKing and Elite boards run higher |
| Swing arm or slide operator replacement | $650 – $1,800 | Includes removal of old unit and setup of new |
| Capacitor, gear, or motor repair | $180 – $480 | Often first-visit fixable on common brands |
| Seasonal tune-up | $89 flat | Lubrication, travel check, sensor test, battery check |
The real cost drivers are the brand, the age of the operator, and how much of the gate has been running on a failing part. A Mighty Mule arm on a residential driveway is a different job than a commercial-grade DoorKing slide gate; both are things we do. Older swingset-style arms in the Historic District area often need new bolts and mounting hardware along with the repair, because the concrete has shifted over the decades and we won’t hand back a motor we didn’t seat properly. We’ll always tell you when the honest answer is “this is close to end of life” so you can decide between repair and replacement – we’re not going to patch a unit that’s going to fail again in six months without saying so.
The 5% Senior and Veteran discount applies to every job, always – not a promotion, just the price. Call (888) 276-7609 for a free estimate.
What to check before you call
- Is the operator plugged in and is the breaker tripped? Obvious, but it’s a real percentage of calls.
- Are the safety sensors facing each other with a clear line of sight?
- Does the remote work from inside the house but not from the driveway? That’s usually a battery or antenna.
- Has anything changed in the last week – storm, power outage, new landscaping, a kid who found the manual release?
If none of that solves it, that’s what we’re here for. We’ll be there when we say.
FAQs – Automatic Gate Repair
Can you fix my automatic gate the same day?
Same-day automatic gate repair is often possible in Boulder City – most jobs are done on the first visit, because we carry common parts for the nine brands we service. If the specific part needs ordering, we give you the timeline the same day, and if you’re stuck with a gate that won’t close, we’ll tell you how to secure the driveway in the meantime. Call (888) 276-7609 and we’ll give you a real answer, not a window.
Is it cheaper to repair or replace my gate operator?
Repair is almost always cheaper in the short term, and we’ll quote it honestly. The rule we use: if the repair costs more than about half the price of a new operator and the unit is already past ten years old, replacement is usually the better money. If the control board, motor and hardware are in decent shape, fixing what failed is the right call. We’ll walk you through both numbers before you decide.
How much does automatic gate repair cost in Boulder City?
Automatic gate repair in Boulder City typically runs $95 to $275 for sensor, remote and keypad work, and $280 to $1,800 for control board or full operator replacement. The exact figure depends on the brand and the failure. We quote upfront, in writing, before we start – and if the job is over $250, the standing $50 off applies. Call (888) 276-7609 for an exact quote; estimates are free.
What brands of automatic gate operators do you service?
We’re trained and equipped on nine: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters because the correct diagnosis and the correct part differ brand to brand, and a wrong guess costs you a second visit. If you’re not sure what’s on your gate, tell us what it looks like and we’ll usually know before we arrive.
Do you offer a warranty on automatic gate repair?
Yes. Every automatic gate repair is covered by our written 90-Day Done Right Promise. If something we touched isn’t right, we come back and make it right – no paperwork, no arguing. It applies on every job, not just the big ones.
Related Services
If your gate needs more than the operator, we handle the full scope. Learn about Gate Repair in Boulder City for structural work, welding, hinges and hardware. Homeowners in the surrounding areas can reach us the same way – we also serve Henderson, Las Vegas, and Hamilton. For gate motor and opener work in Boulder City, visit our gate motors and openers page. Keypad and access work is covered under gate access control. And for hinges, wheels, tracks and fabricated parts, see gate parts and welding. Curious what a tune-up includes? Read our gate tune-up guide. Comparing repair to replacement? Our repair-or-replace guide for gate openers lays out the math. For installation of a new automatic gate, see gate installation. For details on the automatic gate repair process and guarantees, our automatic gate repair overview covers what to expect. If you’re looking at other repair topics, our gate repair FAQ answers the questions we hear most.
Call Ironworks Gate Co. Boulder City
If your automatic gate is doing something it shouldn’t, call (888) 276-7609 for a free estimate. A live person answers, 24 hours a day, 7 days a week. Our technicians have up to 13 years of experience, they’re background-checked and uniformed, and they arrive with a written price you approve before any work starts. Backed by the 90-Day Done Right Promise. We’ll be there when we say, and we stand behind it.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City.