Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Henderson
If your driveway gate has stopped opening, reversed halfway, or started dragging on the concrete, we can help. We handle gate repair throughout Henderson – Green Valley, Anthem, Seven Hills, Lake Las Vegas, and the neighborhoods off Horizon Ridge and Eastern – and we know how these gates were built because we work on them every week. Call (888) 276-7609 and a live person answers, day or night. You’ll get an upfront price before any work starts, and every repair is backed in writing by our 90-Day Done Right Promise.
Why Ironworks Gate Co. Boulder City Is Henderson’s Preferred Gate Repair Company
Henderson homeowners call us back, and that’s most of our business here. They call back because the technician who shows up is background-checked, uniformed, and trained on the operator bolted to their driveway – whether that’s a LiftMaster, a Linear, or an older Elite unit. Our technicians have up to 13 years of experience, and they’ve seen what sixteen summers of desert heat do to a control board.
We work across the Henderson ZIP codes – 89011, 89044, 89012, and 89074 – and we know the drive. That means when you call about a gate that won’t close at 7 a.m., we can tell you plainly when we’ll be there. No voicemail tree, no callback queue. A live person answers every call, 24 hours a day, 7 days a week.
What earns repeat work in Henderson is the documentation side of the job. Our techs understand HOA architectural-approval paperwork, and they carry the color references and hardware notes that Green Valley and Anthem design-review boards expect. That’s a different skill than swinging a wrench. It’s the reason a repair that passes inspection the first time is worth more here than the lowest bid.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Gate Repair Services in Henderson
Automatic Gate Repair
Most of the automatic gate calls we run in Henderson’s master-planned subdivisions come down to the operator, not the gate. After a few summers above 100°F, builder-grade swing and slide operators stall, reverse mid-travel, or stop responding to the remote entirely. We test the control board, the safety photocell, and the loop detector before we touch the panel itself, so the actual fault gets fixed on the first visit.

Hinge & Post Repair
A gate that sags and drags usually points to the hinge post, not the hinge. In Sun City Anthem and Sun City MacDonald Ranch, we regularly find dried-out rubber hinges and posts whose footings have shifted in the caliche-heavy soil. We check the footing for cracks and settle before deciding whether to re-hang the gate or reset the post. That single decision keeps the gate swinging true instead of sagging again in six months.

Electric Gate Repair
Electric gates need clean, dedicated power, and in Henderson’s newer subdivisions that power run is often the problem. When a gate was installed manual at build-out and automated later, the conduit and dedicated circuit frequently weren’t buried during construction. That leads to exposed wiring, voltage drops, and operators that fail again and again. We trace the whole circuit and tell you what the install actually needs – including the trench and conduit – before quoting a number. If the repair is electrical work that puts you near line voltage, we’ll say so and send a trained professional rather than have you open the housing.

Gate Realignment
Monsoon wind gusts and blowing dust rack gate frames and clog tracks and photo-eye sensors. A gate can look fine and still be out of square enough that the operator strains every time it moves. We check alignment against the posts and the operator’s travel limits, realign the frame, and clean out the track and sensor lenses so the gate closes smoothly through the next wind season. A gate realigned properly also stops chewing through hinges.
Trusted Brands We Service in Henderson
We’re trained and equipped on nine gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That range matters in Henderson, where one street of newer homes can carry three different operators from the builder. We don’t claim to stock parts on a truck – we diagnose the fault, order what’s needed, and schedule the return visit so it’s done once. When a DoorKing board or a LiftMaster logic board is the problem, we know which one it is before we leave. For the full scope of what we handle, see our Gate Repair services page.
Common Gate Repair Problems We See in Henderson Homes
- Builder-grade operators failing early. The LiftMaster and Linear units installed during the 1990s-2010s building boom often overheat on west-facing driveways, where the sun bakes the housing all afternoon. Dried-out rubber seals and heat-stressed control boards are the usual culprits, not the gate panel.
- Manual gates automated without power or conduit. Many Henderson gates went in manual and were automated years later. Without a buried dedicated circuit, the operator runs on undersized wire, drops voltage, and fails repeatedly.
- HOA finish mismatches. A replacement panel or off-the-shelf hinge that doesn’t match the community’s approved powder-coat color can trigger a compliance notice even though the gate works fine. Matching the finish before the panel goes up avoids the second trip.
- Warped frames and clogged sensors after monsoon season. Rare wind gusts rack frames out of square, and dust settles into tracks and photo-eye lenses. A gate that worked all spring can start reversing for no visible reason.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Repair in Henderson, NV
A typical hinge and post repair in Henderson runs $180 – $420. Automatic gate operator repair usually lands between $250 and $650, depending on whether the control board, motor, or safety devices need replacing. Electric gate repair involving wiring or a conduit run runs $300 – $900. Gate realignment is often $150 – $300. Those ranges are real for this market, but every gate is different, so we quote and agree on the price before a single bolt is turned. No surprises on the bill. Estimates are free, and there’s $50 off any repair over $250, plus a permanent 5% senior and veteran discount. Call (888) 276-7609 for an exact number.
We Also Serve Cities Near Henderson
We work the whole southeast valley, so if you’re just outside Henderson, we can still help. Our Henderson coverage runs out into Boulder City, Whitney, Paradise, and Enterprise, and the same 90-Day Done Right Promise and upfront pricing apply wherever you are. Call and we’ll tell you when we can be there.
Serving Henderson, NV – Our Local Coverage Area
We serve Henderson and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs – Gate Repair in Henderson
Yes. We match the community’s approved iron finish and hardware before ordering, so a repaired or replaced gate passes design review. In Green Valley and Anthem, the review board cares about the exact powder-coat color and hardware, so we note what’s required up front rather than after the fact. That’s the difference between a repair that’s approved and one that gets flagged. Call (888) 276-7609 to get started.
Intense desert sun and 100°F+ summers dry out rubber seals and overheat control boards, especially on west-facing driveways. The operator isn’t honestly failing – the heat is wearing it out faster than the manufacturer expected. When we service a LiftMaster or Linear unit in Henderson, we check the seals and board condition, not just whether it opens today. Call for an exact quote; estimates are free.
Usually yes, but it’s often more than an operator swap. In Henderson’s newer subdivisions, the dedicated power and conduit that an automated gate needs frequently weren’t buried when the home was built, so we have to run them. That makes it a multi-trade job rather than a one-visit fix. We’ll look at the site and give you a written price that includes the power run before anything is ordered.
It’s usually the hinge post, not the hinge. We check the footing for cracks or settle in Henderson’s soil before deciding whether to re-hang the gate or reset the post. Fixing the hinge alone on a shifted post just means the gate sags again in a few months. Call (888) 276-7609 and we’ll take a look.
Automatic gates need working safety devices – at minimum photocell sensors and, on many installations, a loop detector – so the gate reverses if something is in its path. We test both on every automatic gate repair. If a safety edge or sensor is bad, we say so because it’s a genuine hazard, not an upsell. Call for a free estimate.
Get Your Henderson Gate Fixed
If your gate is dragging, reversing, or flat-out refusing to move, don’t wait for it to get worse. Call Ironworks Gate Co. at (888) 276-7609 for a free estimate. A live person answers 24 hours a day, 7 days a week. You’ll get an upfront price agreed before any work starts, background-checked technicians, and a written 90-Day Done Right Promise behind every job. Done right – and backed in writing.
Written by the team at Ironworks Gate Co.