Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Hinge & Roller Replacement: The Boulder City Owner’s Guide
We replace failed Ghost Controls hinges and rollers on driveway gates throughout Boulder City, and most jobs run $185 to $390 installed depending on how many hinges and rollers your gate carries and whether the weld plates need repair. In many cases we can get to a Boulder City gate the same day you call. Owners usually find the problem the same way: the gate starts dragging at the latch end, the roller squeals through the middle of its travel, or the opener strains and reverses halfway open as if something is fighting it.
That last symptom is the one that surprises people. A worn roller adds drag the actuator has to overcome, and the safety system reads the extra resistance as an obstruction. The gate is not broken. The hardware under it is.
Which Ghost Controls Models This Applies To
Ghost Controls builds its residential line around a handful of single and dual swing actuator kits, and the gate hardware underneath is shared across them more than most owners expect. The hinge and roller components are sized to the gate leaf and the post, not to the actuator model. That means the part number you need is driven by your gate’s weight, its width, and the post material far more than by whether you have a single or dual setup. A dual-leaf driveway in Boulder City gets the same hinge family as a single-leaf entry gate of similar weight.
To identify the correct part, measure three things before you order anything: the gate leaf width, the leaf weight (or the closest estimate you can make), and the post tube dimensions where the hinge mounts. Look for a manufacturer label on the actuator arm and on the control box, and photograph the existing hinge and roller from two angles. Ghost Controls-compatible hardware comes in more than one post-mount configuration, and the mounting plate that fits a steel tube post will not fit a wood post without an adapter.
On the OEM-versus-aftermarket question, our honest answer is that a quality aftermarket hinge or roller rated for your gate’s weight does the job. What matters is the weight rating and the material, not the label on the bag. We are an independent service provider and not affiliated with Ghost Controls, so we source what fits and holds up rather than what carries a brand premium. The one place we would not cut corners is the roller bearing: a cheap sealed bearing fails fast in Boulder City’s dust and heat.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Hinge & Roller Replacement Is Failing
Hinges and rollers do not fail all at once. They fail in a sequence, and catching the early stage saves the gate and the opener.
- The gate sags at the latch end. A hinge pin has worn oval inside its barrel, so the leaf drops a quarter inch or more and the latch no longer lines up. Left alone, the sag puts twisting stress on the top hinge and the weld plate.
- The gate drags or scrapes through part of its swing. A flat-spotted or seized roller is rolling instead of turning, or a hinge has lost its grease and is binding. This is the stage where the opener starts working harder than it should.
- The opener strains, beeps, or reverses on its own. The added drag from worn hardware trips the obstruction sensor, so the gate reverses as if something is in the way. Owners often replace the opener board before realizing the hardware is the cause.
- Squealing, grinding, or a metallic click at the hinge. The bearing or bushing has dried out or the pin has worn through its plating. In Boulder City’s heat and windblown grit, an ungreased hinge gets there faster than most people expect.
- Visible rust, play, or a cracked weld at the hinge plate. The pin moves in its barrel when you push the gate by hand, or the weld where the hinge meets the gate frame has started to crack. This one is a safety issue and should not wait.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Boulder City depends on how many hinge and roller points your gate has, the gate’s weight, and whether the mounting plates or welds need repair. Here is what we typically see:
| Work | Typical installed range |
|---|---|
| Single hinge replacement (parts and labor) | $185 – $260 |
| Single roller replacement (parts and labor) | $150 – $220 |
| Full hinge and roller set, single-leaf gate | $320 – $390 |
| Weld plate repair or re-hang, added | $90 – $180 |
The parts-plus-labor breakdown is transparent: the hardware is a modest line item and the labor is the rest. What drives the range up is gate weight, post condition, and a hinge plate that has to be cut out and rewelded. Every price is quoted and agreed before a single bolt is turned, so there are no surprises on the bill. The work is covered by our written 90-Day Done Right Promise: if a hinge or roller we installed is not right, we come back and make it right.
DIY or Call Us?
Some things an owner can safely check. Open the gate by hand with the opener disengaged and feel for drag, listen for a squeal, and look for play at the hinge pin when you push the gate sideways. Grease and a visual inspection are reasonable owner tasks.
Where DIY goes wrong on this part is the swap itself. Hinges and rollers carry the full weight of the gate leaf, and a gate that comes off its hinge while you are working under it is heavy enough to cause real injury. On a dual-leaf or wide driveway gate, the weight and leverage are more than one person should manage. The pin has to come out cleanly, the mounting plate has to seat true, and the gate has to be rehung square or the new part fails early and the opener keeps straining. We would rather you call than work under a loaded gate. If your hardware is failing, call us at (888) 276-7609 and we will tell you honestly whether it can wait or needs a same-day visit.
FAQs
Expect five to ten years on a well-greased hinge and roller in Boulder City conditions, with the lower end on gates that face full afternoon sun and dust. The heat and wind-driven grit here dry out a bushing faster than in cooler climates, and a hinge that is never greased can flat-spot a roller well before the five-year mark. Regular greasing is the single cheapest thing you can do to stretch that lifespan. Call (888) 276-7609 for a free estimate if you are unsure where yours stands.
Sometimes, yes. A hinge that is binding but not worn oval can often be cleaned, greased, and kept in service, and a roller with a dry bearing can sometimes be revived for a while. Once the pin is worn out of round, the weld plate is cracked, or the roller has flat-spotted, replacement is the only fix that holds. We will tell you which you are looking at before any work starts.
A single hinge or roller swap is usually a done-in-one-visit job, often within an hour or two on a standard gate, while a full set with weld repair can run into a half day. We confirm the scope and the price upfront, so you know what the visit involves before we begin. Call (888) 276-7609 to get on the schedule.
We match the hinge and roller to your gate’s weight, width, and post configuration rather than to a single model number, and we source quality hardware rated for that load. We are an independent service provider and not affiliated with Ghost Controls, so we choose what fits and holds up. We also service LiftMaster, Mighty Mule, and DoorKing gates when that is what is on your driveway. Call (888) 276-7609 for a free estimate.
When a hinge or roller fails on a Boulder City gate, the fix is straightforward for someone who does it every day. Live phone support answers every call, 24 hours a day, 7 days a week, and we will give you a straight answer on whether it is a same-day job. Call (888) 276-7609 for a free estimate on your Ghost Controls hinge and roller replacement in Boulder City.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.