Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Gate Installation in Boulder City: What to Know First
Ghost Controls gate installation in Boulder City is scheduled work, not same-day work. We measure your driveway first, order the correct operator and accessories to match your gate’s weight and swing, and most residential installs take about three to five hours once the unit is on site. Prices are quoted in writing before we touch anything, and the final bill matches the quote. This page is for homeowners who already own Ghost Controls equipment – or have decided on it – and want an independent company to install or replace it correctly. As an independent Ghost Controls service provider, Ironworks Gate Co. Boulder City is not affiliated with or authorized by the manufacturer, and that independence is exactly what keeps our advice honest. Call (888) 276-7609 for a free estimate.
How Ghost Controls Products Fail – and How We Fix Them
Ghost Controls makes solid, homeowner-friendly solar and low-voltage operators, but they fail in predictable ways, and Boulder City’s climate makes some of those failures worse. Here is what we actually see:
- Corroded control boards on the TDS/ARS panel-mount series. Ghost Controls boards live in the same enclosure as the battery, and Boulder City’s dry-season dust plus occasional monsoon humidity collects on the terminals. The classic symptom is a gate that runs when you press the remote but stops dead when the photo-eye beam breaks – a sign the board is reading the safety input as a fault. We clean, test, and replace the board with a sealed, weather-rated unit rather than blaming the remote.
- Fatigued actuator arms on swing operators. The screw-drive actuator on a Ghost Controls swing arm is rated for a specific gate weight, and an older wrought-iron gate in Boulder City can quietly creep past that limit as hinges stiffen. The arm then binds, drains the battery, and eventually strips the screw. Our fix is to free up or rebuild the hinges first, then verify the actuator is sized correctly – replacing the operator without addressing a binding gate just buys you another failure.
- Solar panel and battery starvation (a real Boulder City reality). Many Ghost Controls units run on a solar panel with no hardwired power. In shadier parts of town – think driveways under mature eucalyptus near the historic district – the panel can’t recover the draw, and the gate slows and stops mid-afternoon. We test the panel output and battery under load, then either re-aim the panel or run dedicated low-voltage power where it makes sense.
- Photo-eye and safety-edge faults after a landscape change. Ghost Controls safety accessories are simple, but the alignment is fussy. A new gravel border or a shrub trim can shift a reflector or shade the beam, and the gate reverses or refuses to close. We re-aim the beam, check the edge sensor resistance, and confirm the reverse-on-contact behavior before we leave.
- Mounting and weld failures on the post or arm bracket. A Ghost Controls operator bolted to a post that has loosened, or hung off a bracket that was tack-welded years ago, will twist under load. The symptom is a gate that jams at one end of the travel. We weld or re-seat the bracket properly and align the arm so the operator pulls in a straight line.
If you have a LiftMaster, Mighty Mule, or DoorKing on the property instead, we service those too – the diagnosis changes, but the discipline doesn’t.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Ghost Controls Gate Installation Process
Every Ghost Controls job follows the same sequence, whether it’s a fresh install, a replacement, or an upgrade on an existing gate:
- 1
Free measurement and consultation. We look at the gate, the hinges, the post, the power situation, and the swing path. We confirm the Ghost Controls model and accessories that fit, and write the price before any work is scheduled.
- 2
Parts decision. We use OEM Ghost Controls parts when they’re the right call and quality aftermarket parts when OEM availability or pricing doesn’t serve you. We tell you which and why, and we keep the warranty intact by following the manufacturer’s installation requirements.
- 3
The install or repair. Mounting, wiring, panel placement, beam alignment, and safety-edge check – done to the same standard on job 400 as job one.
- 4
Full test cycle. Open, close, reverse-on-contact, and battery draw under load. We walk the gate’s travel and watch it, we don’t assume.
- 5
Walkthrough and cleanup. We show you how the operator and remotes work, clean up the site, and leave you with the written 90-Day Done Right Promise – the Keystone Standard – on the whole job.
See the difference
Before
After
Before
After
Before
AfterWhat Ghost Controls Gate Installation Costs in Boulder City
Here are realistic ranges for the Ghost Controls work we do. Your actual price depends on the gate, the site, and the model – these are guides, not quotes.
| Scenario | Typical range |
|---|---|
| Ghost Controls swing operator install on an existing hung gate | $650 – $1,100 |
| New driveway gate with Ghost Controls operator and accessories | $2,200 – $4,500 |
| Replacement board or battery/service call | $180 – $340 |
| Solar panel re-aim plus battery replacement | $220 – $400 |
| Safety-beam re-alignment and edge-sensor check | $150 – $300 |
What moves the price: gate weight and width, whether power needs to be run, hinge or weld repairs, and the number of remotes and access points. Parts are quoted separately and up front. We settle the price in writing before a single bolt is turned, and the bill you get is the bill you agreed to. Call (888) 276-7609 for a free estimate.
Why Boulder City Homeowners Call Ironworks Gate Co. Boulder City for Ghost Controls Work
We’re a dedicated gate specialist, not a handyman who happens to own a wrench. Our technicians have up to 13 years of experience, and every job is backed by the written 90-Day Done Right Promise – no paperwork, no arguing: if it isn’t right, we come back and make it right. We’re trained and equipped across nine automation brands, including Ghost Controls, LiftMaster, Mighty Mule, and DoorKing, so whatever is on your driveway gets the right diagnosis the first time. Most jobs are finished in a single visit, and a live person answers the phone 24 hours a day, not a voicemail tree. We also keep standing offers that save you real money: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% Senior and Veteran discount. Boulder City homeowners call us because the job gets done once, correctly, and guaranteed in writing.
FAQs
Ghost Controls gate installation in Boulder City typically runs $650 to $1,100 on an existing hung gate, and $2,200 to $4,500 for a new gate with the operator and accessories. The final price depends on gate weight, site conditions, and whether power needs to be run. Call (888) 276-7609 for an exact quote – estimates are free.
In most cases we repair the operator rather than replace it. A failed board, a binding actuator arm, or a dead battery is often fixable on a single visit, and we tell you honestly when a repair makes sense versus when a replacement is the better value. We quote both before any work starts.
Installing to the manufacturer’s requirements keeps your Ghost Controls warranty intact, and we follow those requirements on every job. We use OEM parts where warranty terms call for them and tell you clearly when a quality aftermarket part is the smarter choice and how it affects coverage.
Ghost Controls installation is scheduled work, not emergency work, so we measure first and schedule your install – typically within a few days of the measurement. Once we’re on site, most residential installs take about three to five hours. Call (888) 276-7609 and we’ll find a time that works.
Yes. We handle the full scope: panel placement, battery and load testing, photo-eye alignment, and safety-edge checks, plus running dedicated low-voltage power where solar alone won’t carry your gate. Safety accessories are tested under a full open-close cycle before we call the job done. Call (888) 276-7609 to schedule a free estimate.
A full installation includes measuring the gate and site, mounting the operator and brackets, wiring, panel or power setup, beam and safety-edge alignment, a full open-close and reverse-on-contact test, a walkthrough of the controls, and site cleanup – all covered by our written 90-Day Done Right Promise.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.