Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Motor Replacement: The Boulder City Owner’s Guide
DoorKing gate motor replacement in Boulder City typically runs $650 to $1,450 installed, depending on the model and whether the control board and battery survive the swap. We stock the common DoorKing-compatible actuators and can often complete a straightforward replacement the same day you call. Most owners don’t wake up planning this purchase. They notice the gate slowing on its last two feet of travel, or the arm cycling twice before it latches, and by the next weekend it stops mid-swing with the car on the wrong side. When a DoorKing operator quits in Boulder City, it usually does so in July or August, and heat is almost always part of the story. We handle DoorKing, and we also service LiftMaster, Mighty Mule, and Ghost Controls when that is what’s on the driveway.
One point of clarity before anything else: Ironworks Gate Co. Boulder City is an independent service provider. We are not affiliated with DoorKing, and we don’t speak for them. We just know their equipment well.
Which DoorKing Models This Applies To
DoorKing builds two broad families that matter for a replacement decision. The 6000 series swing operators (6002, 6050, 6400 and the like) drive a gate arm through a gearbox, and the 9000 series slides run a chain or rack. Within each family, the actuator is matched to gate weight and leaf width, so a motor pulled from a 12-foot single swing will not carry a 16-foot double. The model plate is usually inside the operator housing, and the rated capacity is stamped there. Photograph that plate before you call anyone.
Here is the compatibility gotcha that catches Boulder City owners: DoorKing changed control-board voltage and connector pinouts across production runs within the same model number. A replacement actuator built for a later board will not plug into an earlier harness, and the reverse is true. Matching by model name alone is not enough. We match by model, plate data, and board revision. On the OEM-versus-aftermarket question, we fit genuine DoorKing actuators on newer operators still under any coverage, and we’ll openly recommend a quality aftermarket equivalent on older units where the price difference no longer makes sense. You get the honest call either way. Our technicians have up to 13 years of experience with this exact decision.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your DoorKing Gate Motor Replacement Is Failing
- The gate slows near the end of travel. That is usually a tired motor winding or a binding hinge forcing the operator to work harder than it should. Left alone, the motor overheats and the thermal cutout starts tripping.
- It cycles two or three times before latching. A weak actuator or a failing limit switch sends the gate back and forth hunting for a position it can no longer find. This is the most common early warning.
- You hear the motor run but the gate doesn’t move. The gearbox or drive coupling has stripped. On DoorKing swing arms, this often follows years of ungreased movement in desert grit.
- The operator is hot to the touch after one cycle. Boulder City summer heat pushes an aging motor past its rating fast. A unit that ran cool in April can bake itself in a single August afternoon.
- The board throws error codes or the gate reverses for no reason. Sometimes the motor is fine and the board is failing. We test both before recommending a replacement, so you don’t pay for a motor you didn’t need.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Boulder City depends on three things: the actuator itself, the condition of the control board, and whether the gate hardware needs attention while we’re in there. A straightforward swing-operator replacement lands in the $650 to $1,050 range. Slide operators and heavier estate gates run $950 to $1,450. If the board also needs replacing, add $200 to $350.
| Line item | Typical installed range |
|---|---|
| Swing operator actuator, standard residential | $650 – $1,050 |
| Slide operator, standard residential | $950 – $1,450 |
| Control board (added when needed) | $200 – $350 |
| Safety edge or loop sensor check and reset | $75 – $150 |
Every price is quoted and agreed before we turn a single bolt. Parts and labor are broken out so you can see exactly what you’re paying for. The work is protected by our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right, no arguing. At $250 and above, the $50 repair credit applies.
DIY or Call Us?
Safe checks an owner can make: confirm the gate swings freely by hand with the operator disengaged (a binding gate kills motors fast), look for cracked or corroded wiring at the harness, and photograph the model plate. That’s it. Here’s where DIY goes wrong: gate operators run on 120-volt household power, and the control board and battery hold a charge even after you kill the breaker. A mistaken meter reading or a swap under load can shock you, and a miswired actuator or failed safety-edge can send a 400-pound gate closing on a person. That’s a genuine hazard, not a scare tactic. The motor replacement itself is a job for a trained technician. Call us at (888) 276-7609 and we’ll tell you honestly whether it’s a motor, a board, or something simpler. Free second opinion on any written estimate you already have.
FAQs
How long does a DoorKing gate motor last in Boulder City? Most DoorKing residential operators last 10 to 15 years, but Boulder City heat and fine desert dust shorten that. Motors that cycle several times a day and never get serviced often fail closer to 8 to 10 years. An $89 seasonal tune-up is the cheapest way to stretch that number.
Can the motor be repaired instead of replaced? Sometimes, yes. A failing limit switch, a worn coupling or a loose connector can be fixed at a fraction of replacement cost. If the winding itself is shorted or the gearbox is stripped, replacement is the sound choice. We test before we quote, so you’re not sold a motor you don’t need. Call (888) 276-7609 for a free estimate.
How long does the swap take? A standard swing-operator replacement is typically a two to three hour job once the correct actuator is on hand. Slide operators and jobs that include board work can run four to five hours. Most of our Boulder City customers are handled in a single visit.
How do you source the right part? We identify your operator by model plate and board revision, then order the exact replacement actuator that matches both. If a genuine DoorKing part is back-ordered, we’ll tell you plainly and offer a quality aftermarket equivalent so your gate isn’t sitting open. You’ll know the source and the price before we order.
If your DoorKing operator is failing in Boulder City, call Ironworks Gate Co. Boulder City at (888) 276-7609 for a free estimate. A live person answers 24 hours a day, 7 days a week. We’ll identify the model, quote a square deal upfront, and back the work in writing. (888) 276-7609.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.