Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
See the difference
Before
After
Before
After
Before
AfterElectric Gate Repair in Boulder City, NV
Electric gate repair in Boulder City usually means one of three things: an operator that has stopped responding to the remote, a motor that runs but the gate won’t move, or a gate that reverses, drags, or jerks before it closes. Most of these are fixed in a single visit once we’ve tested the control board, the safety sensors, and the physical travel of the gate together. Call Ironworks Gate Co. Boulder City at (888) 276-7609 and get a straight answer from a live person, day or night.
We handle the electrical and mechanical side of the gate as one system, because that’s how the failures actually happen. A LiftMaster operator with a burned-out board is often fighting a hinge that has been binding for months. A DoorKing keypad that “stopped working” is often a wiring fault at the pedestal, not the unit itself. We’re trained on nine gate-automation brands, and our technicians bring up to 13 years of experience to the diagnosis. If the underlying gate hardware needs attention first, you’ll find that scope covered on our Gate Repair page.
Boulder City gate owners tend to keep their gates a long time. That suits us, because we’re the company that makes a 40-year-old gate close like the day it was hung.
Key Takeaways
- Most electric gate failures in Boulder City are diagnosed and repaired in a single visit.
- We service LiftMaster, DoorKing, Elite, Mighty Mule and five other major brands.
- You’ll get an upfront price before we turn a bolt, and a written 90-Day Done Right Promise when we’re done.
- A live person answers the phone 24 hours a day, 7 days a week at (888) 276-7609.
When You Need Electric Gate Repair
Electric gates rarely fail without warning. There’s usually a season of small complaints first. These are the ones we hear most often from homeowners around Boulder City, where hard water, blowing desert grit, and summer heat all work against moving metal.
- The remote stops working, but the wall button still opens the gate. That points to the receiver or the remote itself, not the motor. LiftMaster and Elite receivers are common culprits, and a quick pairing test tells us which side is at fault.
- The gate opens but won’t close, or reverses partway. In our experience this is usually a safety-sensor problem: a misaligned photo-eye, a pinched loop wire at the driveway, or debris on the lens. On an older gate it can also be a travel limit that has drifted out of adjustment.
- The motor hums but the gate doesn’t move. Stop troubleshooting at the operator. A humming motor with no gate travel can mean a stripped gear, a slipping chain, or a roller that has seized in its track and is fighting the motor. Running a motor against a stuck gate is how small repairs become expensive ones.
- The gate binds, shudders, or drags on the ground. Grit in the track, a sagging hinge, or a worn roller will overload the operator over time. This is the single most common cause of premature motor failure we see in the area, and it’s why we always check the gate’s physical travel before we touch the electronics.
- The keypad or entry code stops working. DoorKing and similar access-control units are reliable, but the pedestal wiring and the battery backup are the parts that wear. A failed backup battery will lock you out the first time the power blinks.
- The gate won’t open manually during an outage. If your manual release won’t free the gate, that’s a safety concern, not a convenience one. It needs attention before the next power cut.
Our Electric Gate Repair Process
Here’s what a service call looks like from the moment you call us to the moment we hand the gate back to you.
- You reach a live person. No voicemail tree, no callback queue. We take your details, ask what the gate is doing, and schedule a time. If it’s an emergency, we’ll tell you honestly what we can do and when.
- We inspect the gate before the operator. We check hinges, rollers, tracks, stops, and the gate’s alignment first. This is where we catch binding and sag that would otherwise burn out the new motor.
- We test the electrical side. Control board, receiver, photo-eyes, safety loops, keypad, and battery backup. On a LiftMaster or Elite system we run a full diagnostic so the correct fix is made the first time, whatever is on the drive.
- We give you an upfront price in writing. No surprises on the bill. Every repair over $250 also gets $50 off, and we offer a free second opinion on any written estimate from another company.
- We do the repair. Most jobs are done in a single visit. If a part has to be ordered, you’ll know exactly what’s happening and when we’ll be back.
- We test the full cycle with you watching. Open, close, reverse, manual release, and safety sensors. When we leave, the gate works, and you’ve seen it work.
Electric Gate Repair Pricing in Boulder City
Electric gate repair in Boulder City typically runs $150 to $650 for a single-visit repair, depending on what failed. A photo-eye realignment or remote pairing usually lands at the low end. A control-board or motor replacement sits at the high end, and on some older units it makes more sense to discuss replacing the operator rather than repairing it. You’ll get a firm price before we start, and you don’t pay for a trip just to hear the number.
| Repair type | Typical range |
|---|---|
| Remote / receiver diagnosis & repair | $150 – $220 |
| Safety sensor / photo-eye realignment | $150 – $250 |
| Limit and travel adjustment | $150 – $250 |
| Keypad or access-control repair (e.g. DoorKing) | $200 – $400 |
| Control board replacement | $350 – $600 |
| Motor / operator replacement | $500 – $1,200+ |
A few things move the number: whether the gate is a swing or slide design, whether it’s a single or double gate, the brand and age of the operator, and whether the gate’s physical hardware needs work too. A gate that has been binding for a year will often need a hinge or roller repair alongside the electrical fix.
Standing offers apply on every job: $50 off any repair over $250, a free second opinion on any written estimate, an $89 seasonal tune-up, and a permanent 5% senior and veteran discount. Estimates are free. Call (888) 276-7609 for yours.
If you’re weighing repair against replacement, our Gate Repair in Boulder City page walks through the full picture, from hinge and weld repairs to component-level replacements. And if your gate’s frame or track is bent, you’ll want to start with our home page to see the full scope we cover.
FAQs – Electric Gate Repair
How much does electric gate repair cost in Boulder City?
Electric gate repair in Boulder City typically costs $150 to $650 for a single-visit job, with most sensor, remote, and limit repairs landing under $250 and motor or control-board replacements at the upper end. The final number depends on your operator brand, whether the gate hardware needs attention too, and whether parts are in stock. Call (888) 276-7609 for an exact quote – estimates are free.
Can you repair my electric gate the same day?
Most electric gate repairs in Boulder City are handled in a single visit, and same-day service is often possible when you call early. A live person answers the phone 24 hours a day, 7 days a week, so you’re never stuck waiting until Monday. Call (888) 276-7609 and we’ll tell you honestly what we can do and when.
Which gate brands do you service?
We service nine major gate-automation brands, including LiftMaster, DoorKing, Elite, Mighty Mule, FAAC, BFT, Linear, Viking, and Ghost Controls. Being trained across the full range means the correct fix gets made on the first visit, whether your gate is a LiftMaster slide operator or an older Mighty Mule swing unit. Call (888) 276-7609 to confirm your model.
Is it cheaper to repair or replace an electric gate operator?
Repair is usually cheaper when the operator is under roughly ten years old and the failure is a sensor, receiver, or limit switch. Replacement tends to make better sense when the motor is aging, the control board has failed twice, or the gate’s physical hardware is fighting the operator. We’ll give you both numbers honestly and let you decide. Call (888) 276-7609 for a free estimate on either path.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City.