Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Parts & Welding in Boulder City: What to Know First
We provide independent DoorKing gate parts and welding in Boulder City, and most hinge, roller, rail and post jobs are done in a single visit once we’ve seen the gate. As an independent DoorKing service provider, we’re not affiliated with or authorized by DoorKing, but we work on their operators and hardware constantly and we’ll tell you plainly whether the part can be repaired or has to be replaced. The price is quoted and agreed before a single bolt is turned, backed by our written 90-Day Done Right Promise, and estimates are free.
This page is for the homeowner with a DoorKing on the driveway who needs a real answer about parts, welds and what it costs. Call (888) 276-7609 and a live person will pick up, day or night.
How DoorKing Products Fail – and How We Fix Them
DoorKing hardware is built heavy and it’s built to last, which is exactly why the failures we see in Boulder City are about steel and mounting, not the electronics. Here are the ones that come up most on a DoorKing gate job:
- Sagging hinges on older swing gates. The weight of a long leaf slowly wears the hinge pin and bends the bracket, so the gate drags at the bottom of the swing. We replace the hinge set, weld-reinforce the bracket and re-align the leaf to the post instead of just tightening what’s already tired.
- Rail corrosion at the welds on desert gates. Boulder City’s sun and dry air bake the finish off the bottom rail first, and the moisture that does collect migrates straight to the weld seams. Left alone, a seam rusts from the inside out. We grind the affected area, weld fresh metal in, and treat the seam so it holds.
- Post loosening in caliche and rocky soil. This is the one that surprises out-of-town techs. The ground here sets hard, then cracks and settles around a post after a wet winter. A post that looks plumb on Monday can lean by spring, throwing off the operator and the latch. We assess the footing and set or reset it properly.
- Roller and track wear on sliding DoorKing operators. Grit gets into the roller bearings and the gate starts to shudder or run slow. We service or replace the rollers and check the track for the buildup that causes premature motor strain.
- Latch and lock misalignment. Once a gate shifts a quarter inch, the latch catches and the lock won’t throw clean. We correct the alignment at the source rather than forcing the latch to do work it can’t do.
None of these are DoorKing design faults. They’re the natural result of heavy steel, dry heat and ground that moves, and every one of them is fixable.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our DoorKing Gate Parts & Welding Process
Here’s exactly how a DoorKing parts and welding job runs, from the phone call to the cleanup:
- 1
The call. A live person answers, asks what the gate is doing, and books a time that works for you. We’ll be there when we say.
- 2
Diagnosis on site. Our technicians (up to 13 years of experience) inspect the hinges, rails, posts, rollers and latch, and find the actual cause instead of treating the symptom.
- 3
The parts decision. We explain whether an OEM part is needed or a quality aftermarket part does the job safely and well, and why. You decide with the facts in front of you.
- 4
The repair. Welding, hinge replacement, rail repair, post work, rollers, latch and lock – done to the metal, not patched over.
- 5
The full test. We run the gate through its full cycle, check the alignment and confirm the latch and operator work together before we call it finished.
- 6
The written promise. Every job is covered by our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat DoorKing Gate Parts & Welding Costs in Boulder City
Most DoorKing parts and welding jobs in Boulder City land between $150 and $650, depending on what’s actually failed. Here’s roughly what the common scenarios run:
- Hinge replacement (one side): $150 – $280
- Gate rollers or track service: $120 – $250
- Rail repair or custom welding: $180 – $400
- Post reset or replacement: $350 – $900
- Latch and lock replacement: $140 – $300
What moves the price is straightforward: the material and thickness of the gate, whether a post has to be reset, and whether the part is OEM or quality aftermarket. The price is agreed before we start, so there are no surprises on the bill.
Call (888) 276-7609 for a free estimate – it costs nothing to find out what your DoorKing gate actually needs.
Why Boulder City Homeowners Call Ironworks Gate Co. Boulder City for DoorKing Work
We’ve been doing this work in Boulder City long enough to know what fails and why, and our technicians have up to 13 years of experience on the tools. That said, the reason homeowners call back is the way we treat the job. A live person answers every call. The technicians who show up are background-checked and uniformed. The price is settled upfront, and it’s backed in writing by our 90-Day Done Right Promise.
We’re trained on nine gate-automation brands – DoorKing, LiftMaster, Mighty Mule, Ghost Controls, FAAC, BFT, Linear, Viking and Elite – so whether your gate has a DoorKing operator or a different brand altogether, we bring the right knowledge on the first visit. Our 5% Senior and Veteran discount is always honored, and there’s a free second opinion on any written estimate.
FAQs
Our welding and parts work is covered by our written 90-Day Done Right Promise, not a manufacturer warranty. DoorKing’s own warranty covers the operator and its parts, but wear on hinges and rails is considered normal use. If a part we repair or replace fails inside 90 days, we come back and make it right.
We can source DoorKing parts for most common hinge, roller, latch and hardware needs, and we’ll tell you upfront when a quality aftermarket part is the smarter, faster choice. For operator electronics, OEM is often the right call. Call (888) 276-7609 with your gate model and we’ll get an answer fast.
Repair almost always beats replacement when the operator and frame are sound and only the hinges, rails or posts have failed. Replacement only makes sense when the frame has rusted through in multiple places or the post can’t be reset. We’ll give you the honest answer, not the expensive one.
For repair jobs, most visits can be scheduled within a day or two, and emergency calls get a live person around the clock. Installation and full automation work is scheduled after a free measure and written price. Call (888) 276-7609 and we’ll find a time that works.
Our typical DoorKing job covers the hardware that actually fails under use – hinges, rollers, latch and lock, rails and posts, and the welding that ties them together. We test the full gate cycle before we leave so the DoorKing operator runs the way it should.
Whether it’s a sagging hinge, a rusted rail or a post that’s drifted out of line, we’ve seen it on a DoorKing gate in Boulder City and we know how to fix it right. Call (888) 276-7609 for a free estimate, and let us make a 40-year-old gate close like the day it was hung.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.