Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateDoorKing Gate Repair in Boulder City: What to Know First
We provide independent DoorKing gate repair in Boulder City, and most repair visits are finished in a single trip once we’ve confirmed the model and the fault. Typical repairs run $185 to $520 depending on the part, and you’ll have the price in writing before a single bolt is turned. We’re an independent DoorKing service provider, not affiliated with or authorized by the manufacturer.
This page is for the homeowner with a DoorKing operator on the driveway – a 6400, a 1500 series slide gate, an older 9000 swing unit – that has started to act up. You’ve probably had it for years and you want it fixed once. Call us at (888) 276-7609 and a live person will answer, any hour.
How DoorKing Products Fail – and How We Fix Them
DoorKing builds solid equipment, but forty years in the desert does its work on any brand. These are the failures we see most on DoorKing units around Boulder City:
- Slide gate coasting or stopping short (1500 and 1600 series). The limit switches drift, or the magnetic encoder loses its reference after a power bump. Boulder City sits in a wind corridor off the McCullough Range, and dust works into the slide track and the encoder housing. We clean and re-reference the limits, and replace the encoder if the magnet has weakened. On these units a “motor failure” diagnosis from a generalist is often a $40 sensor, not a $900 operator.
- Swing-arm operator binding or grinding (6400 and 6500 series). The arm linkage and the operator’s gearbox wear together, and a hinge that has sagged a quarter inch pulls the whole gate out of line. The operator then fights the gate every cycle. We realign the gate and hinges first, then check the gearbox, because replacing the operator on a misaligned gate just buys the same failure again.
- Board and battery faults after monsoon season. DoorKing control boards on the 9000 and 6400 lines are sensitive to voltage sag, and a weak backup battery throws false “obstruction” faults that look like a sensor problem. We test the battery under load before condemning the board. Homeowners have paid for a new board when a $60 battery was the whole story.
- Keypad and entry-system failures (DoorKing 1500 and 1830 series). The keypads and card readers take direct sun on a west-facing post, and the membrane and the board inside cook over a Boulder City summer. We replace the entry unit and, where the post allows, add a shade hood so the next one lasts.
- Weld and hinge corrosion on older installs. Gate frames welded decades ago with plain steel rust at the hinge plates and the operator mount. We cut out the rusted section, weld in new plate, and treat the joint so it holds. A hinge that lets go under an operating arm is a genuine hazard, so we never patch a cracked weld with a brace and move on.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our DoorKing Gate Repair Process
Every DoorKing job follows the same path, whether it’s a keypad swap or a full operator replacement:
- 1
Phone diagnosis. A live person takes your call and asks what the gate is doing and what model DoorKing you have, so we arrive with the right parts.
- 2
On-site inspection. We test the operator, the limits, the safety edges, and the gate’s mechanical alignment. A gate fault is often mechanical before it’s electrical.
- 3
Parts decision. We quote OEM DoorKing parts and quality aftermarket where it makes sense, tell you the trade-off in plain terms, and let you choose. No surprises on the bill.
- 4
The repair. Welding, realignment, board work, or operator replacement, done to spec and tested at the gate.
- 5
Full cycle test. We run the gate through multiple open and close cycles, check the safety reverse, and confirm the limits hold.
- 6
The guarantee. Every job is backed in writing by our 90-Day Done Right Promise. If it isn’t right, we come back and make it right.
See the difference
Before
After
Before
After
Before
AfterWhat DoorKing Gate Repair Costs in Boulder City
Prices below are real ranges for DoorKing work in Boulder City. Your exact price is settled before any work begins, and a free second opinion is available on any written estimate you already have.
| Repair | Typical range |
|---|---|
| Limit switch or encoder reset | $185 – $260 |
| Backup battery replacement | $160 – $240 |
| Hinge and post realignment | $250 – $450 |
| Control board replacement | $340 – $620 |
| Keypad or entry unit swap | $280 – $520 |
| Weld and rust repair | $220 – $500 |
What moves the price: the DoorKing series, whether OEM or aftermarket parts are chosen, and how much of the gate frame needs welding. The quote we give is the price you pay. Call (888) 276-7609 for a free estimate.
Why Boulder City Homeowners Call Ironworks Gate Co. Boulder City for DoorKing Work
We’ve served local communities for over 42 years, and our technicians have up to 13 years of experience on gate automation. We’re trained and equipped on nine leading brands – LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule – so whatever operator is on your driveway, the correct fix happens on the first visit. Most DoorKing jobs finish in one trip, priced upfront and backed in writing by the 90-Day Done Right Promise. A live person answers the phone 24 hours a day, seven days a week. Our technicians are background-checked and uniformed, guided by our K.E.Y.S. values: Krafted right, Every time, Your home first, Standing behind it. Standing offers include $50 off any repair over $250, a free second opinion, an $89 seasonal tune-up, and a 5% senior and veteran discount.
FAQs
Repair work itself does not void a DoorKing warranty, but using non-OEM parts during an active warranty period can. We check your model and warranty status before recommending parts, and we’ll steer you to OEM on a unit still under coverage so the warranty stays intact.
Yes. We source OEM DoorKing parts and quality aftermarket equivalents, and we tell you which is which. On a unit still under warranty we recommend OEM; on an older operator, aftermarket can save you real money with no meaningful drop in reliability.
Most DoorKing repairs are done in a single visit, and a live person answers your call 24 hours a day so we can talk through the fault before we arrive. Call (888) 276-7609 for the fastest route to a repair slot.
Repair usually wins when the operator is under 12 to 15 years old and the fault is a board, sensor, battery, or mechanical part. On a unit older than that with a failed gearbox and a rusted frame, replacement often costs less over the next decade. We give you both numbers so the choice is yours.
Yes. We service LiftMaster, Mighty Mule, Ghost Controls, and six other major brands, so your neighbor’s gate gets the same treatment as yours. Call (888) 276-7609 for a free estimate.
If your DoorKing gate needs a real fix, backed in writing, call Ironworks Gate Co. Boulder City at (888) 276-7609 for a free estimate. A live person answers any hour, and we’ll give you the price before we turn a single bolt.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.