Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGhost Controls Access Control Installation: The Boulder City Owner’s Guide
Access control installation on a Ghost Controls system typically runs $650 to $1,450 installed in Boulder City, depending on whether you’re adding a keypad, a wireless entry station, or full telephone or app entry. Most jobs are done in a single visit, and we quote a firm price before we touch the gate. We’re an independent service provider and not affiliated with Ghost Controls, though Ghost Controls is one of nine automation brands our technicians are trained and equipped to service.
Owners usually find out something in the access side has gone bad the same way: the keypad beeps but the gate never moves, or the entry station works from the car and dies at the pedestrian path. That gap between “it powers on” and “it actually triggers the operator” is where access control problems live. Sometimes the board has failed. Sometimes it’s a wiring or power issue the panel has been masking. Here in Boulder City, where summer surface temperatures climb past 110°F and the sun hits a west-facing keypad for eight hours a day, we see plastic housing and membrane keypads go brittle years before their rated service life.
Which Ghost Controls Models This Applies To
Ghost Controls builds its access control accessories around its own low-voltage control board, and the board changed across model generations. If you’re matching a replacement keypad, entry station, or receiver, the generation of your operator matters more than the brand name on the box.
The easiest identification is the control board itself. Open the operator housing and look for the model and revision silkscreened onto the board, plus the terminal layout: older boards group the accessory terminals one way, newer boards add a dedicated accessory power output. The revision string on the board is what we ask for when a customer calls, because ordering a keypad for the wrong generation is the most common mistake we correct. Aftermarket keypads and receivers are widely sold as “Ghost Controls compatible,” and many genuinely are, but compatibility claims get looser as the aftermarket gets cheaper. We install OEM parts when an owner wants the original fit and finish, and quality aftermarket equivalents when the price gap is significant and the part genuinely matches the board. Either way, we tell you which we’re putting in and why before we order it. Beyond Ghost Controls, we also service LiftMaster, Mighty Mule, and DoorKing systems, so we’re not steering every call toward one brand.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Ghost Controls Access Control Installation Is Failing
Access components on a Boulder City gate usually fail for one of four reasons, and the symptom tells you which. Here’s what we see most often:
- Keypad lights up but the gate never opens. The keypad is getting power but its signal isn’t reaching the operator, which usually means a failed receiver, a dead channel on the board, or a wire that’s corroded at the splice. Desert temperature swings work on exterior splices in a way owners don’t expect.
- Code accepted, then nothing, or a delayed response. This is the classic sign of a failing control board or a receiver losing its learned code. On older boards the accessory terminal block can also loosen from heat cycling.
- Gate opens from inside but not from the exterior station. Power or signal is dying somewhere between the station and the operator. Nine times out of ten it’s a wiring or low-voltage transformer issue, not the station itself.
- Works in the cool morning, fails by mid-afternoon. Heat-related board or component failure. In Boulder City, a west-facing keypad or exposed control box sits in direct sun for hours, and marginal electronics fail at temperature.
- Only the phone or app entry fails. The network or telephone module has dropped off the board, or the board’s accessory power output is under-voltage. This is a diagnosis problem, not a parts-guessing problem.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed pricing in Boulder City falls into these ranges, and every quote is settled in writing before any work starts:
| Access control work | Installed range |
|---|---|
| Replacement keypad or exterior entry station | $185 – $350 |
| Replacement receiver or wireless module | $150 – $280 |
| Control board accessory section repair or replacement | $240 – $520 |
| Low-voltage wiring repair or transformer replacement | $160 – $400 |
| Full access control installation (keypad, entry station, and app or phone entry) | $650 – $1,450 |
The range comes down to parts choice, wiring distance, and whether we’re replacing a component or correcting a diagnosis someone else guessed at. Labor, removal of the old part, and a test of every entry point are included in the price you agree to. The work carries our written 90-Day Done Right Promise: if it isn’t right, we come back and make it right.
DIY or Call Us?
There are things you can safely check yourself. Confirm the operator has power, look at the control board for a blown fuse or a visibly burnt terminal, and note whether the failure changes with temperature or time of day. Those observations help us diagnose fast when you call.
Where DIY goes wrong on access control is the low-voltage and entry side. The components sit on a 12-volt or 24-volt circuit tied to the operator’s control board, and a miswired keypad or wrong transformer can damage the board itself, turning a $200 part into a $500 repair. Exterior wiring buried in desert ground also presents hazards, and we don’t recommend homeowners dig or splice it. This isn’t a dangerous-part page like gate springs, but the cost of guessing is real. Call (888) 276-7609 for a straight answer on what’s likely failing and what it’ll cost to fix.
FAQs
Most exterior keypads and entry stations last seven to twelve years; the shorter end is common on west-facing mounts where UV and heat break down plastic and electronics faster. Interior control boards typically outlast them. When we replace one, we often reposition a sun-baked mount to the shaded side of a pillar at no extra labor charge.
Sometimes. A failed receiver or loosened accessory terminal can often be repaired for less than a replacement, while a cracked membrane keypad or a board with a burnt channel is usually a replacement. We diagnose first and tell you which, with the price of each, before we do anything. Call (888) 276-7609 for an honest call on it.
A keypad or entry station swap is usually done in one visit, often within an hour or two once the correct part is on hand. Board-level repair or a full access control installation can run most of a day. We tell you the timing when we quote.
We order directly from the manufacturer or a verified aftermarket supplier once we’ve confirmed your board revision, and we never guess at a part and hope. We also offer a free second opinion on any written estimate, so if another shop has quoted an access part, we’ll review it with you before you commit.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.