Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateMighty Mule Hinge & Roller Replacement: The Boulder City Owner’s Guide
We replace Mighty Mule gate hinges and rollers with model-matched parts, and most Boulder City jobs run $180 to $420 installed depending on the gate style and how much hardware has seized. We keep same-day slots open for jammed or dragging gates, and every job is quoted and agreed in writing before we touch a bolt.
Owners usually find the problem the same way. The gate starts to sag at the latch and the pin no longer drops clean. Or you push it open and hear a grind at the hinge knuckle, or the roller skips off the track and the gate digs into the driveway slab. In Boulder City’s dry heat, the factory grease in Mighty Mule hinge pins cooks out faster than most people expect, and once the pin runs dry it wears the bore instead of the pin. Some owners notice a bright stripe of bare metal on the track, a sign the roller bearing has locked and is sliding instead of rolling. We’ve seen this on older gates on Nevada Way and around the Lakeview neighborhood, and it’s almost always the roller, not the whole gate arm.
Which Mighty Mule Models This Applies To
Mighty Mule sells hinge and roller hardware across its swing and slide lines, and the parts are not interchangeable between them. The swing-gate hinge sets for the Mighty Mule 350, 360, and 500 series are the most common we see in Boulder City. The slide gates and the heavier dual-gate brackets use a different post bracket and roller wheel. If you can’t find a model sticker, look for it on the control box lid or the underside of the opener arm, then measure the hinge pin diameter and the gap between post and gate frame before you order anything.
The OEM-versus-aftermarket call matters more on Mighty Mule than on premium brands. Mighty Mule’s original hinge pins are a softer steel than what’s on a LiftMaster or DoorKing gate, and a quality aftermarket pin in a harder grade often outlasts the original. The trade-off is a small risk of a slightly different bore size. That’s why we match the part to the measured pin rather than to the model name alone. If you own a Ghost Controls or DoorKing gate instead, tell us on the call and we will bring the right hardware for that brand too.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Signs Your Mighty Mule Hinge & Roller Replacement Is Failing
- Latch won’t line up. A hinge pin worn past a few thousandths of an inch lets the gate drop at the free end. The opener then fights the misalignment, and the latch strike misses.
- Grinding or squealing at the hinge. The grease has dried and the pin is riding on bare metal. Left alone, it wears the hinge barrel and you’re replacing the whole bracket instead of a pin.
- Roller skips or drags on the track. The roller bearing has seized, so the wheel slides instead of rolls. You’ll see a flat spot on the wheel or a shiny streak on the track.
- Gate sags when you push it open by hand. Could be a hinge, a roller, or a tired post, and the fix is different for each. We check all three before quoting.
- Opener strains or reverses on the first foot of travel. A binding hinge or roller loads the motor, and the unit senses the resistance and reverses. That’s often logged as a fault when the real problem is the hardware, not the operator.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Installed hinge and roller replacement in Boulder City runs like this:
| Job | Typical installed range |
|---|---|
| Single hinge pin replacement (one hinge) | $180 – $240 |
| Full hinge set, one gate leaf | $260 – $360 |
| Roller wheel or track roller replacement | $200 – $300 |
| Hinge set plus rollers, one leaf | $340 – $420 |
| Post bracket repair or re-weld | $250 – $450 |
Price includes the part, the labor, and a check that the gate swings and latches clean when we’re done. The range moves on gate weight, how rusted the old hardware is, and whether the post bracket needs re-welding. It is settled with you before we start, so the bill you get is the number you agreed to. Every job is covered by our 90-Day Done Right Promise: if it isn’t right, we come back and make it right, in writing.
DIY or Call Us?
You can safely check a few things yourself. Push the gate open by hand and feel for binding. Look for a worn pin, a flat spot on a roller, or a bright stripe on the track. Grease a dry hinge and see if the grind goes away. What we’d steer you away from is pulling a seized hinge pin on a loaded gate, or cutting and re-welding a post bracket. A gate under spring or motor tension can swing or drop the moment a hinge lets go, and a dropped gate on a driveway is a real injury risk. We’re trained on Mighty Mule and eight other brands, and most of these jobs are done in a single visit. If yours is jammed or dragging, call us at (888) 276-7609 and we’ll get it on the schedule.
FAQs
Expect about three to six years on original hardware in Boulder City’s dry heat, sometimes less on a gate that sits in full sun on a south-facing driveway. The factory grease dries out fast, and once the pin runs dry it wears quickly. Keeping the pins greased extends the life.
Often the roller bearing can be cleaned and re-greased, or a single worn pin swapped without replacing the whole hinge set. If the hinge barrel that holds the pin is worn or wallowed out, that piece has to be replaced. We check which it is before quoting, so you don’t pay for hardware you didn’t need. Call (888) 276-7609 for a free estimate.
Most single-leaf jobs take one to two hours, and a gate that needs both hinges and rollers plus a bracket repair can run three or more. We tell you the time up front so you can plan around it. Most Boulder City jobs are done in a single visit.
We match on the measured hinge pin diameter and bracket spacing, not on the model sticker alone, and we cross-check against the Mighty Mule opener model on your control box. We’re an independent service provider, not affiliated with Mighty Mule, but we’re trained and equipped on the whole line. If your part is out of stock locally, we order the correct one and tell you the lead time before you commit.
If your gate is dragging, grinding, or failing to latch, don’t wait for it to bind the opener. Call Ironworks Gate Co. at (888) 276-7609 for a free estimate on Mighty Mule hinge and roller replacement in Boulder City. A live person answers every call, 24 hours a day, seven days a week. We also service LiftMaster, Ghost Controls, and DoorKing gate hardware.
Written by the team at Ironworks Gate Co. Boulder City, serving Boulder City and nearby areas.